Water expands as it freezes, and that pressure can split a pipe in an exterior wall, an unheated basement or a crawl space. The damage usually shows after the thaw, when water flows again. Know where your main shutoff is, close it at the first sign of a break, and then call a technician.
Key takeaways
- A pipe usually does not leak while it is frozen; the split shows when the ice thaws and the water starts moving again, which is why a burst often announces itself hours after the coldest point.
- Roughly half of New London's homes date from before 1940, and older houses tend to have supply lines running through exterior walls, basements and crawl spaces where cold reaches first.
- A regional newspaper report on one cold stretch in the city described broken pipes at a nursing facility that had to move patients out of one wing, and firefighters kept busy pumping basements.
- The main shutoff valve is the single most useful thing to locate before a cold snap, because closing it limits how much water reaches the house once a split opens.
- A frozen pipe that has not yet burst can be thawed slowly with gentle warmth, never with an open flame, and the water should stay off until the pipe has been looked over.
- Standing water from a burst needs to be extracted and the structure dried quickly, because wet drywall, insulation and framing hold moisture long after the surface looks dry.
Why do pipes burst when the weather turns very cold?
Water expands as it turns to ice. Inside a closed length of pipe, that expansion raises the pressure between the ice plug and the nearest closed valve or faucet, and the pipe can split at its weakest point.
People often picture the ice itself cracking the pipe, but the usual failure is a pressure problem. When a section freezes, the ice blocks the line, and any water trapped between the blockage and a closed tap has nowhere to go. As more of it freezes and expands, pressure climbs in that trapped stretch, and the pipe gives way where the wall is thinnest, at a joint, or at a spot already weakened by corrosion or an earlier freeze. The split can be a hairline that only weeps or a long tear that sprays.
That is also why a burst is so often discovered late. While the ice is in place it acts like a plug in the damaged pipe. The trouble begins when the temperature rises, the plug softens and the water supply pushes through a hole that was waiting for it. A homeowner who left for the day in a cold house can come back to a wet ceiling, a flooded basement or a stream running down a wall, with no warning in between.
Which parts of an older New London house are most exposed?
Supply lines in exterior walls, unheated basements, crawl spaces, garages and attics are the usual trouble spots. They sit closest to outdoor cold and farthest from the heat the living space gets.
Census-based summaries of American Community Survey data put about 47 percent of New London's housing units as built in 1939 or earlier, so a plain way to put it is that roughly half of the city's homes date from before 1940. Houses of that age were plumbed and renovated in layers over many decades. A kitchen added to the back of a house may have its sink line running along a cold outside wall, and a bathroom squeezed under a sloped roof may have pipes in a cavity that gets little warmth.
Look at where water enters the building and where it travels from there. A line that comes through a masonry foundation wall, runs along a basement ceiling near a rim joist or crosses an unheated crawl space is within reach of outdoor air. So are hose bibs and the pipes that feed them, outdoor shower lines and any plumbing in an enclosed porch. A pipe tucked into an insulated interior partition has far better odds than one against an uninsulated exterior sheathing board.
What has a cold stretch actually done in New London before?
A regional newspaper report on one cold stretch described broken pipes across New London, including at a nursing facility that had to move patients out of one wing, while firefighters were kept busy pumping basements.
That report is worth reading for what it shows about scale. A burst pipe in a single house is a household emergency. A burst in a building full of residents becomes a logistics problem, with people moved out of the affected wing while the water is stopped and the area is dried and repaired. The same account noted that firefighters were kept busy pumping out basements, which tells you that the damage did not stay in one neighborhood or one kind of building. The report is undated here because the source gave no date that could be confirmed.
The point for a homeowner is practical. Cold-driven breaks tend to cluster, because the same weather reaches every pipe at once, and the people who can help are stretched across many addresses at the same time. Preparing before a hard cold arrives, and acting on the first sign of trouble instead of waiting to see whether it clears, puts you ahead of that queue. A house that has been shut off and drained of standing water early is a much smaller job than one that ran for a day.
What should I do before a hard freeze arrives?
Find and test the main shutoff, keep the house heated, open cabinet doors under sinks on exterior walls, let a faucet drip on the coldest nights and disconnect hoses. Insulate what you can reach and seal drafts near pipes.
Start with the shutoff, because it is the one thing that matters most if something fails. Walk the house and find where the main supply line enters, then turn the valve fully closed and open again so you know it moves. A valve that has not been touched in years can seize, and the middle of an emergency is a poor time to discover that. Make sure everyone who lives in the house can find it. Also find the shutoff for the water heater and any isolation valves at individual fixtures, since closing one of those can isolate a problem to a single room.
Then reduce exposure. Keep the heat on and set at a steady level even if the house will be empty, because a cold house is the common thread in many freeze-ups. Open the cabinet doors beneath kitchen and bathroom sinks that back onto an outside wall so room air can reach the pipes. On the coldest nights, a small steady trickle from a faucet on the far end of the plumbing keeps water moving, and moving water is harder to freeze. Disconnect garden hoses, close any interior valve feeding an outdoor tap and drain the line where the plumbing allows it. Foam sleeves on exposed pipes and caulk around penetrations where lines pass through the wall help a little.
How do I tell a frozen pipe from a burst one?
A frozen pipe means water slows to a trickle or stops, with no sign of leaking. A burst pipe shows water on a floor, a stain spreading on a ceiling or wall, a drip from a fixture that is not in use, or the sound of running water.
The early signal is often the faucet. If you turn a tap and only a thin stream comes out, or nothing at all, while other taps still work, a section of that line may be frozen. Frost on the outside of an exposed pipe, a pipe that feels much colder than its neighbors and a faint smell from a drain are other clues. At this stage nothing has necessarily failed, and the goal is to thaw the pipe before it does.
Once the ice melts, listen and look. A hiss or the sound of running water behind a wall when no fixture is open, a bulge or dark patch on a ceiling below a bathroom, a damp baseboard or a puddle at the foot of a basement stair are signs that the pipe has opened. Check the water meter if you can reach it: if the dial is moving while every fixture is off, water is escaping somewhere. When you suspect a break, do not wait for confirmation. Close the main shutoff first and sort out the cause afterward.
How do I thaw a frozen pipe safely?
Open the faucet so melting water can drain, then warm the pipe slowly with a hair dryer or warm towels, working from the faucet toward the frozen section. Never use an open flame, and shut the main off if you find any leak.
Opening the tap matters because it gives meltwater and the pressure behind it somewhere to go. Begin at the end nearest the faucet and move back toward the blockage, so the water can escape as the ice gives way. A hair dryer on a low setting, a heating pad wrapped around the pipe or towels soaked in warm water are all reasonable. Keep electrical cords and appliances well away from standing water, and do not stand in a wet area while using anything plugged in.
Skip anything that produces open flame or intense heat. A torch or heat gun can scorch framing behind a wall, ignite old insulation or boil water in the pipe and make it worse, and in a house with a history of renovation there may be material in the wall you cannot see. If you cannot reach the frozen section, cannot find it, or see the pipe already bulging or cracked, stop. Shut the main supply, keep the house warm and bring in a technician who can open the area and look at the pipe before water is turned back on.
What do I do in the first hour after a pipe bursts?
Close the main shutoff, switch off power to wet areas if it is safe to reach the panel, open taps to drain the lines, move valuables and photograph everything. Then call a technician to extract the water and begin drying.
The first job is to stop the flow. Closing the main shutoff ends the supply, and opening the lowest and highest taps in the house helps drain what remains in the pipes. If water is coming through a ceiling, near a light fixture or around outlets, treat the area as unsafe and turn off the circuit from the panel only if you can get to it without stepping through water. If you cannot, stay out and call for help. Pull up small rugs, lift furniture off wet carpet and move papers, electronics and keepsakes to a dry room.
Then document before you clean. Take wide photographs and close ones of the pipe, the wet surfaces and the items that were damaged, and write down the time you noticed the break and when you closed the valve. Those notes help later with any insurance conversation and with the technician's drying plan. If the water has been standing for a while, call (833) 490-5225 and describe what you see; a technician can talk you through what to hold off on and arrange extraction. Do not run a household vacuum on standing water and do not try to dry a soaked ceiling by waiting.
Why does drying matter after the water is stopped?
Water from a split pipe soaks insulation, drywall, flooring and framing, and it does not leave on its own quickly. Extraction, air movement and dehumidification bring materials back to a dry state before mold or rot has a chance.
A wall that looks fine after a burst can be saturated inside. Insulation soaks up water like a sponge, drywall draws it up from the bottom edge, and the framing and subfloor hold moisture for far longer than the surface suggests. A technician uses moisture meters to find where the wet material really ends, which is often further than the stain you can see. Extraction removes what can be pumped or vacuumed, then fans and dehumidifiers move air across wet surfaces and pull vapor out of the room.
The tradeoff in these jobs is speed. The longer materials stay wet, the more likely they are to need replacing instead of drying in place, and the more likely it is that mold will start. A clean-water break from a supply line is the easier end of the range, but it can still involve opening a wall or lifting flooring to reach trapped moisture. Insurance wording varies from policy to policy; sudden bursts are typically treated differently from slow leaks, which is a reason to keep your dated photographs and notes. Ask your insurer what your own policy says.
Frequently asked questions
Will a frozen pipe always burst?
No. Many frozen pipes thaw without splitting, especially when the ice forms slowly or the pipe is flexible or has some give. But you cannot tell from outside whether the pipe has been weakened, and a break can open as the ice melts. Treat any frozen line with caution, thaw it gently and check it for leaks once water is flowing again. If you see dripping or a wet patch near it, shut the main and get it looked at.
Should I leave the heat on if I am away from home?
Generally yes. A house left unheated is a common setting for a freeze-up, because the pipes lose the warmth that kept them above the danger point. Set the thermostat to a steady level, open cabinet doors on exterior walls and ask someone to look in on the house if you will be gone for a while. If you have a way to be alerted to a power cut or a leak, that gives you a head start.
Where is my main water shutoff likely to be?
In many older homes it sits in the basement or crawl space near where the line comes through the foundation, often close to the meter. In others it is in a utility closet or under a kitchen sink. Walk the house before a cold spell, find the valve, and test that it turns. Tell everyone in the household where it is, and consider a tag so a visitor can find it quickly.
Is it safe to use a space heater to warm a cold basement?
Be careful. A space heater near damp materials or standing water is a hazard, and heaters left running unattended near stored items can start a fire. If you need to warm an area to protect pipes, use equipment rated for the purpose, keep it clear of anything combustible and never run one in a wet space. A safer first step is closing drafts and opening cabinet doors so the house heat reaches the pipes.
Does home insurance usually cover a burst pipe?
Home policies generally treat sudden and accidental water damage, such as a burst, differently from slow leaks and seepage. Coverage is set by the wording of your own policy, so read the water section and ask the insurer to confirm in writing. Keep your photographs, a timeline of when you shut the water off and any receipts. The Connecticut Insurance Department takes complaints if a claim is handled badly.
How long does it take to dry out after a burst pipe?
It varies with how much water escaped, which materials got wet and how quickly extraction began. A technician takes moisture readings, sets equipment and checks again until the structure reaches a dry reading, so the end point is measured instead of guessed. A small break caught early is a short job. A long run behind a wall or under a floor takes more time and can involve opening up surfaces.
This guide is general information for New London County homeowners, not a substitute for an on-site inspection. Prices are estimates. See our disclaimer.